Register FAQ Calendar Search Today's Posts Mark Forums Read
Navigation
Front Page
Forum
Gallery
Wiki

Ads by Google


Go Back   Hamster Central > >

Notices

Reply
 
Thread Tools Display Modes
Old 07-09-2011, 10:26 AM   #1
Queen Of The High Teas
The Hambassador
 
Queen Of The High Teas's Avatar
 
Join Date: Jun 2011
Location: Oop north (Wales that is!)
Posts: 1,737
Default Cutting plastic?

I have decided after seeing the wonderful settle on here, that some of my cages are a little to small, especially Gypsy my Chinese, who loves to dig and can't in a bar cage, so I have bit the bullet and gotten a bin in wilko's today. It is much bigger than her cage and I'm really looking forward to making it. If it turns out okay I intend to do a couple more as well. But does anyone know how can I cut the plastic in the lid to fix the wire to without cracking the lid? The last time I tried drilling plastic it cracked the whole thing, so I need to get this right! Help anyone???
__________________
🐶1 dog, 🐭1 chin, 🐹 1 ham

🐾🌈❤️RIP to all my Bridge babies❤️🌈🐾
Queen Of The High Teas is offline   Reply With Quote
Old 07-09-2011, 10:32 AM   #2
wiggle'smommy
Senior Hamster
 
wiggle'smommy's Avatar
 
Join Date: Dec 2010
Location: South Africa
Posts: 484
Default Re: Cutting plastic?

This is what I did because I don't have a lot of tools, I used a craft knife. You can light a candle to heat the blade in every few minutes because that will help melt through the plastic as well as cut it. First make shallow scores so that you know where to cut and then cut deeper one section at a time (a few cm at a time) and go round the whole thing. Once the cut is deep (almost completely severed) sink the knife all the way through at a point and then slide it along the cut slowly (moving the blade up and down as you go along). That should do it!
__________________

<3 Wiggles
RIP Nugget and Regis
wiggle'smommy is offline   Reply With Quote
Old 07-09-2011, 10:34 AM   #3
mangoandmimi
Little Miss Tinytoes
 
mangoandmimi's Avatar
 
Join Date: Aug 2010
Location: UK
Posts: 7,040
Default Re: Cutting plastic?

i did the same as wiggle, with an old kitchen knife haha :') Works pretty well, just be patient and dont rush it or it cracks :P
and i just heated it over the hob :P (held it above it,..)
mangoandmimi is offline   Reply With Quote
Old 07-09-2011, 12:27 PM   #4
racinghamster
PM Fluffy for custom title
 
racinghamster's Avatar
 
Join Date: Jul 2006
Location: Central Scotland
Posts: 13,413
Default Re: Cutting plastic?

Melting it slowly as you cut with a craft knife or some kind of stanley knife sounds the best way. I tend to melt holes in plastic by using a metal knitting needle and holding it over the gas ring! I`ve never tried to melt away a longer strip though.

You could also use a soldering iron which would give you a better cut.
__________________
Get A Life, Get A Rodent!
racinghamster is offline   Reply With Quote
Old 07-09-2011, 03:15 PM   #5
Ham Ham Hamstery
Banned
 
Join Date: Mar 2011
Location: Ohio
Posts: 1,698
Default Re: Cutting plastic?

I have an xacto knife try getting one they work good heat the blade of it so it melts the plastic
Ham Ham Hamstery is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Powered by vBulletin®
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Parts of this site powered by vBulletin Mods & Addons from DragonByte Technologies Ltd. (Details)
Copyright 2003-19, Hobby Solutions Inc.
All times are GMT -7. The time now is 04:25 AM.